AMX AXB – REL8 PDF

The AXB-REL8 controls closure-activated devices, acting as an eight-channel relay control port on the AxLink bus. Find great deals for AMX Axb-rel8 Access Relay Controller. Shop with confidence on eBay!. AMX AXB-REL8 Relay Controller | Consumer Electronics, Surveillance & Smart Home Electronics, Other Smart Home Electronics | eBay!.

Author: Daigal Najora
Country: Kosovo
Language: English (Spanish)
Genre: Software
Published (Last): 16 June 2010
Pages: 322
PDF File Size: 3.41 Mb
ePub File Size: 13.29 Mb
ISBN: 429-9-44145-242-6
Downloads: 56403
Price: Free* [*Free Regsitration Required]
Uploader: Malalmaran

For details about manual, see the info below. Please inspect the lot numbers and read re8l descriptions. Check cable and source against supplied documentation. The auctioneer reserves the right to cancel, suspend, extend or reschedule an individual item and or auction event or to make changes to the auction closing times or inspection or removal times. When in doubt about condition, completeness or suitability anx intended use, please bid accordingly.

For demonstration purposes various equipment may be joined. Batteries and incandescent lamps are not covered under the warranty. Check operational status of interface or source. The device number must match the device assignment in the Axcess program.

However, when you bid on the wrong item or decide an item is not suited for your intended ax, our clients are not willing to assume the cost of your mistakes.

The file is available in a few seconds as the connection speed of your internet. Insert each wire into the appropriate captive-wire connector up to the insulation. Install supplied tab strips to jumper between shared commons.

The device number is the total of all of the switches in the ON down position. The following table shows the switch numbers and their corresponding values. AMX assigns device numbers into the following three segments: Check continuity of relay wiring. It is the responsibility of the buyer to determine the condition of the items and bid accordingly.

TOP Related Posts  HBDI TEST PDF

AMX AXB-REL8 Relay Controllers, Qty 2

Clip off excess tabs and bend strip up, away from other wiring. This limitation of liability will be effective even if AMX Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such damages.

Browse Bid and Win. Checking the installation After set-up is complete: Software is warranted for a period of ninety 90 days. Check jumpers used for shared commons. Any items left after the specified load out dates will be considered forfeited unless alternate pickup or shipping arrangements are made. This Limited Warranty gives the owner specific legal rights. This includes any lost profits, lost savings, incidental damages, or consequential damages.

We believe that our webpage help you and we will be glad if you visit us in the future. On this page you can download it for free.

This limitation of liability cannot be waived or amended by any person. The closing time of each lot will be automatically extended an additional 5 minutes whenever a bid is placed within the last 5 minutes of the lot closing.

AMX AXB-REL8 Manuals

Load out staff cannot accept any form of payment. Check cable numbers and wiring, interfaces and sources against supplied documentation. Fasten the front panel to the rack and to the unit with the two xab you removed. Refer to the following section for more information. Connecting the Wiring The following paragraphs describe wiring connections for using the AXlink and relay connectors.

TOP Related Posts  EL VENDAJE FUNCIONAL TONI BOVE PDF

This enters the new device number into memory. Descriptions are believed to be accurate but not guaranteed. In such states, the limitation or exclusion of rsl8 Limited Rrel8 may not apply. Tighten the captive screws to secure the fit in the connector. Click image to enlarge. The auction will begin closing at 7: This limitation of liability, however, will not apply to claims for personal injury. Winning bidders may pick their items up at Cornerstone Drive; Belton Missouri.

Relay LED lights, but source does not activate: Do not install relay wiring at this time. Install tab strips to jumper between shared commons and clip off excess tabs.

The dotted lines are used to indicate commons. AMX reserves the right to alter specifications without notice at any time. Is this manual helpful? Remove any aaxb relay and AXlink connectors from the rear panel. Illuminate when associated relay is closed.

Unless otherwise specified, OEM and custom products are warranted for a period of one 1 year. Do not assume a lot consists of more than one item simply because they are connected or pictured together. AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform. Preparing captive wires To connect the wiring into a captive-wire connector: Relay LED’s should match panel control function.